View BFC233610224_6729959.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

not for new design - altern ative series mkp338 1 x1 mkp336 1 x1 www.vishay.com vishay bccomponents revision: 06-aug-12 1 document number: 28117 for technical questions, contact: rfi@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 interference suppression film capacitors mkp radial potted type features ? 15 mm to 27.5 mm lead pitch. supplied in box, taped on ammopack or reel ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 applications x1 class for x1 electromagnetic interf erence suppression in across the line applications (50 hz /60 hz) with a maximum mains voltage of 275 v ac . for application limitations please refer to section application notes. note ? for more detailed data and test requirements, contact rfi@vishay.com quick reference data capacitance range (e12 series) 0.01 f to 1 f (prefe rred values according to e6) capacitance tolerance 20 %; 10 %; 5 % rated ac voltage 275 v ac ; 50 hz to 60 hz permissible dc voltage 630 v dc climatic testing class (accor ding to en 60068-1) 55/105/56/b maximum applicatio n temperature 105 c rated temperature 105 c leads tinned wire reference standards iec 60384-14 2nd edition and en 132400 iec 60065, pass. flamm. class b ul 60384-14 csa e384-14 dielectric polypropylene film electrodes metallized film construction mono construction encapsulation plastic case, epoxy resin sealed, flame retardant ul-class 94 v-0 marking c-value; tolerance; rated voltage; sub-clas s; manufacturers type designation; code for dielectric materi al, only for pitch ? 15 mm; manufacturer lo cation; year and week dimensions in millimeters h l t l p 0.4 w ? d t
not for new design - altern ative series mkp338 1 x1 mkp336 1 x1 www.vishay.com vishay bccomponents revision: 06-aug-12 2 document number: 28117 for technical questions, contact: rfi@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 composition of catalog number note (1) for detailed tape specifications refer to packaging information: www.vishay.com/doc?28139 note (1) see voltage proof test for metalized film capacitors: www.vishay.com/doc?28169 specific reference data description value tangent of loss angle: at 10 khz c ? 100 nf ? 10 x 10 -4 100 nf < c ? 470 nf ?? 20 x 10 -4 c ? 470 nf ?? 70 x 10 -4 rated voltage pulse slope (du/d t ) r at 385 v dc : p=15mm 250 v/s p = 22.5 mm 150 v/s p = 27.5 mm 100 v/s r between leads, for c ? 0.33 f at 100 v; 1 min > 15 000 m ? rc between leads, for c > 0.33 f at 100 v; 1 min > 5000 s r between leads and case; 100 v; 1 min > 30 000 m ? withstanding (dc) voltage (cut off current 10 ma) (1) ; rise time ? 1000 v/s 3400 v; 1 min withstanding (ac) voltage be tween leads and case 2050 v; 1 min bfc2 336 1x xx x 2222(*) 336 1x xx x type packaging lead configuration c-tol. preferred types 336 1 x1 loose in box lead length 3.5 mm 0.3 mm lead length 25.0 mm 2.0 mm lead length 25.0 mm 2.0 mm 20 % bfc2 336 10... . . . 6 1 6 3 3 2 c f b 336 1 x1 loose in box lead length 3.5 mm 0.3 mm 10 % 10 % bfc2 336 11... . . . 7 1 6 3 3 2 c f b taped on reel h = 18.5 mm; p 0 = 12.7 mm; reel diameter 500 mm 20 % bfc2 336 13... bfc2 336 14... type and pitches 336 1 x1 15.0 mm 22.5 mm 27.5 mm multiplier (nf) 0.1 2 13 10 4 100 5 capacitance (numerically) example: 104 = 10 x 10 = 100 nf (*) old ordering code on request
not for new design - altern ative series mkp338 1 x1 mkp336 1 x1 www.vishay.com vishay bccomponents revision: 06-aug-12 3 document number: 28117 for technical questions, contact: rfi@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? spq = standard packing quantity (1) reel diameter = 356 mm is available on request (2) h = in tape height; p 0 = sprocket hole distance; for detailed specifications refer to packaging information. (3) weight for short lead product only electrical data and ordering information u rac (v) cap. (f) dimensions wx hx l (mm) mass (g) (1) catalog number bfc2 336 1 ..... and packaging loose in box reel 500 mm (1)(2) l t ? = ? 3.5 mm 0.3 mm l t = 25.0 mm 2.0 mm h ? 18.5 mm; p 0 ? 12.7 mm last 5 digits of catalog number spq last 5 digits of catalog number spq last 5 digits of catalog number spq 275 pitch = 15.0 mm 0.4 mm; d t = 0.6 mm 0.06 mm; u rac = 275 v; c-tol. = 20 % 0.010 5.0 x 11.0 x 17.5 1 19001 1000 19007 1000 19002 1100 0.015 10153 16153 13153 0.022 10223 16223 13223 0.033 6.0 x 12.0 x 17.5 1.4 10333 16333 13333 900 pitch = 15.0 mm 0.4 mm; d t = 0.8 mm 0.08 mm; u rac = 275 v; c-tol. = 20 % 0.047 7.0 x 13.5 x 17.5 1.8 10473 1000 16473 500 13473 800 0.068 8.5 x 15.0 x 17.5 2.4 10683 16683 13683 650 0.100 10.0 x 16.5 x 17.5 3 10104 500 16104 13104 600 pitch = 22.5 mm 0.4 mm; d t = 0.8 mm 0.08 mm; u rac = 275 v; c-tol. = 20 % 0.10 7.0 x 16.5 x 26.0 2.9 19003 200 19008 500 19004 550 0.15 8.5 x 18.0 x 26.0 3.8 10154 16154 13154 450 0.22 10.0 x 19.5 x 26.0 6.8 10224 16224 13224 400 pitch = 27.5 mm 0.4 mm; d t = 0.8 mm 0.08 mm; u rac = 275 v; c-tol. = 20 % 0.22 11.0 x 21.0 x 31.0 7.4 19005 100 19009 125 0.33 13.0 x 23.0 x 31.0 9.2 10334 16334 0.47 15.0 x 25.0 x 31.0 12.3 10474 16474 0.68 18.0 x 28.0 x 31.0 16.1 10684 16684 1.00 21.0 x 31.0 x 31.0 20.3 10105 50 16105 75 pitch = 15.0 mm 0.4 mm; d t = 0.6 mm 0.06 mm; u rac = 275 v; c-tol. = 10 % 0.010 5.0 x 11.0 x 17.5 1 11103 1000 17103 1000 14103 1100 0.012 11123 17123 14123 0.015 11153 17153 14153 0.018 11183 17183 14183 0.022 6.0 x 12.0 x 17.5 1.4 11223 17223 14223 900 0.027 11273 17273 14273 pitch = 15.0 mm 0.4 mm; d t = 0.8 mm 0.08 mm; u rac = 275 v; c-tol. = 10 % 0.033 7.0 x 13.5 x 17.5 1.8 11333 1000 17333 500 14333 800 0.039 11393 17393 14393 0.047 8.5 x 15.0 x 17.5 2.4 11473 17473 14473 650 0.056 11563 17563 14563 0.068 10.0 x 16.5 x 17.5 3 11683 500 17683 14683 600 0.082 11823 17823 14823 pitch = 22.5 mm 0.4 mm; d t = 0.8 mm 0.08 mm; u rac = 275 v; c-tol. = 10 % 0.10 7.0 x 16.5 x 26.0 2.9 11104 200 17104 500 14104 550 0.12 8.5 x 18.0 x 26.0 3.8 11124 17124 250 14124 450 0.15 11154 17154 14154 0.18 10.0 x 19.5 x 26.0 6.8 11184 17184 500 14184 400 pitch = 27.5 mm 0.4 mm; d t = 0.8 mm 0.08 mm; u rac = 275 v; c-tol. = 10 % 0.22 11.0 x 21.0 x 31.0 7.4 11224 100 17224 125 0.27 11274 17274 0.33 13.0 x 23.0 x 31.0 9.2 11334 17334 0.39 15.0 x 25.0 x 31.0 12.3 11394 17394 0.47 11474 17474 0.56 18.0 x 28.0 x 31.0 16.1 11564 17564 0.68 11684 17684 0.82 21.0 x 31.0 x 31.0 20.3 11824 50 17824 75
not for new design - altern ative series mkp338 1 x1 mkp336 1 x1 www.vishay.com vishay bccomponents revision: 06-aug-12 4 document number: 28117 for technical questions, contact: rfi@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 mounting normal use the capacitors are designed for mounting on printed-circuit bo ards. the capacitors packed in bandoliers are designed for mounting in printed-circuit boards by means of automatic insertion machines. for detailed tape specifications refer to packaging information. specific method of mounting to withstand vibration and shock in order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the printed-circuit board: ? for pitches ? 15 mm capacitors shall be me chanically fixed by the leads ? for longer pitches the capacitors shall be mo unted in the same way and the body clamped space requirements on printed circuit board the maximum length and width of film capacitors is shown in figure: ? eccentricity as in figure. the maximum eccentricity is smaller than or equal to the lead diameter of the product concerned ? product height with seating plane as given by iec 60717 as reference: h max. ? h + 0.3 mm soldering conditions for general soldering conditions and wave solder ing profile, we refer to the application note: soldering guidelines for film capacitors: www.vishay.com/doc?28171 storage temperature ? storage temperature: t stg = - 25 c to + 35 c with rh maximum 75 % without condensation ratings and characteristi cs reference conditions unless otherwise specified, all electrical values apply to an ambient temperature of 23 c 1 c, an atmospheric pressure of 86 kpa to 106 kpa and a relative humidity of 50 % 2 %. for reference testing, a conditio ning period shall be applied over 96 h 4 h by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. approvals safety approvals x1 voltage value file numbers en 60384-14 (enec) (= iec 60384-14 ed-3) 275 v ac 10 nf to 1 f fi 2008058 a1 ul 60384-14 275 v ac 10 nf to 1 f e354331 csa e384-14 275 v ac 10 nf to 1 f e354331 cb-test-certificate 275 v ac 10 nf to 1 f fi 5254 a1 the enec-approval together with the cb-certi ficate replace all national marks of the following countries (they have already sig ned the enec-agreement): austria; belgium; czech. republic; denmark; fi nland; france; germany; greece; hungary; ireland; italy; luxembo urg; netherlands; norway; portugal; slovenian; spain; switzerland and united kingdom. cba11 6 eccentricity l max. = i + 0.3 mm b max. = b + 0.3 mm
not for new design - altern ative series mkp338 1 x1 mkp336 1 x1 www.vishay.com vishay bccomponents revision: 06-aug-12 5 document number: 28117 for technical questions, contact: rfi@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 characteristics capacitance impedance tangent of loss angle resonant frequency max. rms voltage and ac current (sinewave) typical - 50 c/c (%) 2 - 2 - 4 - 6 0 050 100 t amb (c) 4 max. min. impedance ( ) 10 3 10 1 10 -2 10 0 f (hz) 10 6 10 4 10 5 10 7 10 8 10 -1 10 nf 47 nf 100 nf 470 nf 1000 nf 4.7 nf 1 nf 10 1 10 1 10 2 10 3 10 0 10 2 10 3 10 4 10 5 f (hz) dissipation factor (x 10 -4 ) c = 1 f 220 nf < c < 1 f 47 nf < c 220 nf 10 nf < c 47 nf c 10 nf c (nf) 1 10 100 1000 10 000 f (mhz) 10 2 10 1 10 0 10 -1 x1 t amb 105 c ac voltage (v) 10 3 10 2 10 1 f (hz) 10 1 10 2 10 3 10 4 10 5 470 nf 100 nf 47 nf 10 nf 1000 nf 1 nf 4.7 nf ac current (ma) 10 4 10 2 10 0 10 1 f (hz) 10 1 10 2 10 3 10 4 10 5 10 -1 t amb 100 c
not for new design - altern ative series mkp338 1 x1 mkp336 1 x1 www.vishay.com vishay bccomponents revision: 06-aug-12 6 document number: 28117 for technical questions, contact: rfi@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 capacitance application notes ? for x2 electromagnetic interf erence suppression in standard across the line applications (50 hz/60 hz) with a maximum mains voltage of 310 v ac . ? for series impedance applications we refer to application note www.vishay.com/doc?28153 ? for capacitors connected in parallel, normally the proof voltage and possibly te rated voltage must be reduced. for information depending of the capacitance value and the number of parallel connections contact: dc-film@vishay.com ? these capacitors are not intended for continuous pulse application. for these situations capacitors of the ac and pulse programs must be used. ? the maximum ambient temperature must not exceed 110 c. (125 c for less than 1000 h) for c ? 470 nf and 110 c for c > 470 nf. ? rated voltage pulse slope: if the pulse voltage is lower than the rated voltage, the values of the specific reference data can be multiplied by 435 v dc and divided by the applied voltage. inspection requirements general notes 1. sub-clause numbers of tests and perf ormance requirements refer to the sec tional specification, iec-publication en 132400 (iec 60384-14) and section one of this specification. 2. in this table: d = destructive nd = non destructive group c inspection requirements sub-clause number and test d or nd conditions performance requirements sub-group c1a part of sample of sub-group c1 d 4.1 dimensions (detail) as specified in chapters general data of this specification initial measurements capacitance tangent of loss angle: for c ? 470 nf at 100 khz for c > 470 nf at 10 khz 4.3 robustness of terminatio ns tensile: load 10 n; 10 s bending: load 5 n; 4 x 90 no visible damage 10 6 10 5 10 4 0 20 40 60 80 100 t amb (c) rc (s)
not for new design - altern ative series mkp338 1 x1 mkp336 1 x1 www.vishay.com vishay bccomponents revision: 06-aug-12 7 document number: 28117 for technical questions, contact: rfi@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 sub-group c1a part of sample of sub-group c1 d 4.4 resistance to solder ing heat no pre-drying method: 1a solder bath: 260 c duration: 10 s 4.19 component solvent resistance isopropylalcohol at room temperature method: 2 immersion time: 5 min 0.5 min recovery time: min. 1 h, max. 2 h 4.4.2 final measurements visual examination no visible damage legible marking capacitance | ? c/c| ? 5 % of the value measured initially tangent of loss angle increase of tan ? : ? 0.008 compared to values measured initially insulation resistance as specified in section insulation resistance of this specification sub-group c1b part of sample of sub-group c1 d initial measurements capacitance tangent of loss angle: for c ? 470 nf at 100 khz for c > 470 nf at 10 khz no visible damage legible marking 4.20 solvent resistance of the marking: see section general notes; item 5 isopropylalcohol at room temperature method: 1 rubbing material: co tton wool immersion time: 5 min 0.5 min no visible damage 4.6 rapid change of temperature ? a = - 55 c ? b = + 105 c 5 cycles sub-group c1b part of sample of sub-group c1 d 4.6.1 inspection duration t = 30 min 4.7 vibration (see note 3.1) visual examination mounting: see section mounting of this specification procedure b4: frequency range: 10 hz to 55 hz amplitude: 0.75 mm or acceleration 98 m/s2 (whichever is less severe) total duration 6 h no visible damage 4.7.2 final inspection visual examination no visible damage group c inspection requirements sub-clause number and test d or nd conditions performance requirements
not for new design - altern ative series mkp338 1 x1 mkp336 1 x1 www.vishay.com vishay bccomponents revision: 06-aug-12 8 document number: 28117 for technical questions, contact: rfi@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 sub-group c1b part of sample of sub-group c1 d 4.9 shock (see note 3) mounting : see section mounting for more information pulse shape: half sine accelerati on: 490 m/s2 duration of pulse: 11 ms 4.9.2 final measurements visual examination no visible damage capacitance | ? c/c| ? 5 % of the value measured initially tangent of loss angle increase of tan ? : ? 0.008 compared to values measured initially insulation resistance as specified in section insulation resistance of this specification sub-group c1 combined sample of specimens of sub-groups c1a and c1b d 4.11 climatic sequence 4.11.1 initial measur ements capacitance measured in 4.4.2 and 4.9.2 tangent of loss angle: measured initially in c1a and c1b 4.11.2 dry heat temperature: 105 c duration: 16 h 4.11.3 damp heat cyclic test db first cycle 4.11.4 cold temperature: - 55 c duration: 2 h 4.11.5 damp heat cyclic test db remaining cycles sub-group c1 combined sample of specimens of sub-groups c1a and c1b d 4.11.6 final measurements visual examination no visible damage legible marking capacitance | ? c/c| ? 5 % of the value measured in 4.11.1. tangent of loss angle increase of tan ? : ? 0.008 compared to values measured in 4.11.1 voltage proof 1200 v dc ; 1 min between term no permanent breakdown or flash-over insulation resistance ? 50 % of values specified in section insulation resistance of this specification group c inspection requirements sub-clause number and test d or nd conditions performance requirements
not for new design - altern ative series mkp338 1 x1 mkp336 1 x1 www.vishay.com vishay bccomponents revision: 06-aug-12 9 document number: 28117 for technical questions, contact: rfi@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 sub-group c2 d 4.12 damp heat steady state 56 days, 40 c, 90 % to 95 % rh, no load capacitance 4.12.1 initial measurements tang ent of loss angle at 10 khz 4.12.3 final measurements visual examination no visible damage legible marking capacitance | ? c/c| ? 5 % of the value measured in 4.12.1. tangent of loss angle increase of tan ? : ? 0.008 compared to values measured in 4.12.1. voltage proof 1200 v dc ; 1 min between term no permanent breakdown or flash-over insulation resistance ? 50 % of values specified in section insulation resistance of this specification sub group c3 d 4.13.1 initial measur ements capacitance tangent of loss angle: for c ? 470 nf at 100 khz for c > 470 nf at 10 khz 4.13 impulse voltage 3 successive impulses, full wave, peak voltage: x1: 4 kv max. 24 pulses no selfhealing breakd owns or flashover 4.14 endurance duration: 1000 h 1.25 u rac at 105 c once in every hour the voltage is increased to 1000 v rms for 0.1 s via resistor of 47 ? 5 % sub group c3 d 4.14.7 final measurements visual examination no visible damage legible marking capacitance | ? c/c| ? 10 % compared to values measured in 4.13.1. tangent of loss angle increase of tan ? : ? 0.008 compared to values measured in 4.13.1. voltage proof 1200 v dc ; 1 min between terminations 2050 v dc ; 1 min between terminations and case no permanent breakdown or flash-over insulation resistance ? 50 % of values specified in section insulation resistance of this specification group c inspection requirements sub-clause number and test d or nd conditions performance requirements
not for new design - altern ative series mkp338 1 x1 mkp336 1 x1 www.vishay.com vishay bccomponents revision: 06-aug-12 10 document number: 28117 for technical questions, contact: rfi@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 sub-group c 4 d 4.15 charge and di scharge 10 000 cycles (50 c/s) charge to u r half sinewave duration: 5 ms discharge resistance: r min. = 2.2 4.15.1 initial measur ements capacitance tangent of loss angle for c ? 470 nf at 100 khz for c > 470 nf at 10 khz 4.15.3 final measur ements capacitance | ? c/c| ? 10 % compared to values measured in 4.15.1. tangent of loss angle increase of tan ? : ? 0.008 compared to values measured in 4.15.1 insulation resistance ? 50 % of values specified in section insulation resistance of this specification sub-group c5 d 4.16 radio frequency characteristic resonance frequency as specified in section resonant frequency of this specification. 10 % sub-group c6 d 4.17 passive flammability class b bore of gas jet: ? 0.5 mm fuel: butane test duration for actual volume v in mm3: v ? 250: 10 s 250 < v ? 500: 20 s 500 < v ? 1750: 30 s v > 1750: 60 s one flame application after removing test fl ame from capacitor, the capacitor must not continue to burn for more than 10 s. no burning particle must drop from the sample. sub-group c7 d 4.18 active flamma bility 20 x 4 kv di scharges on the test capacitor connected to u r the cheese cloth around the capacitors shall not burn with a flame. no electrical measurements are required. group c inspection requirements sub-clause number and test d or nd conditions performance requirements r 385 v dc 1.5 x c du dt ? ?? ------------------------------------------- = 45.0 ~ 8 mm 12 mm
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.

▲Up To Search▲

Price & Availability of BFC233610224

	To Download BFC233610224 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .